This is a listing for individual full metal custom mounting pieces ("H" or "T" style) and individual 1515 extrusion pieces.  These are the same pieces sold within the the Euclid probe dock kit (here).  However, these mount pieces can be used to mount virtually any accessory (purge bucket, wiper brush, LCD mount, etc.) to your 1515 extrusion-based printer.  Each mounting pieces is made from high strength 7075 aluminum and has been designed to provide maximum versatility, usability, and strength.

The "T" shaped mounting piece is designed to attach directly to the 1515 extrusion that makes the frame of your printer, on either a vertical or horizontal frame member, with the included screws and included 713Maker post assembly 1515 T-nuts. Since this mount piece is designed to be used with our 1515 post assembly T-nuts, there is no printer disassembly required to add your accessories using this mount to your 1515 extrusion printer frame.

Please note:  We are now offering 2 different versions of T nuts.  Our original M2.5 T nut was designed to fit the channel dimensions of the Misumi brand 1515 extrusions.  In order to better accommodate the growing variety of 1515 extrusions available, which often have a narrower channel size from the Misumi brand, we are now offering a M2.0 T nut which has an overall narrower form factor and thus is forced to use a slightly smaller M2.0 size screw.  To assist with identification, the M2.0 T nut has 2 dots on the flat, top surface of the nut itself, while the M2.5 T nuts are blank.

Please use the following information to determine which T nut fits the 1515 extrusion that you have.

M2.0 T nut (sold here):  For use with non-Misumi / imported, black or colored, 1515 extrusion.  This extrusion has either 1 or 5 total holes in the ends and a channel size of 3.0mm wide at its narrowest (top) point.  This extrusion would have been purchased from Filastruder, Printed Solid, or AliExpress.  This T nut also fits the Voron V0 and V0.1 and Makerbeam XL 1515 extrusion frames.

M2.5 T nut (sold here):  For use with silver 1515 extrusion.  This extrusion has a single, center, hole in the ends and has a channel size of 3.2mm wide at its narrowest (top) point. This extrusion would have been purchased from R3D, Filastruder, or directly from Misumi, and will use these M2.5 T nuts.

If in doubt order the M2.0 T nut, however please feel free to contact us with any T nut sizing questions, prior to ordering.  No refunds or exchange for purchases of T nuts that are the wrong size.

The "H" piece provides a connection between any 2 1515 extrusion pieces in several different ways.  It has 4 pass through holes (one on each leg of the "H") and one center pass through hole.  You would use 2 of the 4 "H" leg holes to attach it to any 1515 side face and/or use the single center hole to attach it to the tapped 1515 end cap.

Each individual piece of 1515 (Misumi brand) extrusion is approx 50mm each and has each end tapped to M3.

Each piece comes with the hardware listed below.  Additional hardware may be purchased from the hardware section of our website, here.  

Pick from the following choices:

"T" - $12

x1 "T" style full metal custom mounting piece

x1 M3 5mm, high strength, zinc coated, low profile, socket cap screw

x2 M2.0 or M2.5 6mm, socket head screws

x2 713Maker post assembly 1515 T-nuts (M2.0 or M2.5)

"H" - $12

x1 "H" style full metal custom mounting piece

x1 M3 5mm, high strength, zinc coated, low profile, socket cap screw

x2 M3 6mm, button head screws

x2 M3 high strength, zinc coated, alloy nuts

"1515" - $6

x1 1515 (Misumi brand) extrusion piece (approx 50mm)

If you feel that 50mm of 1515 extrusion may not work for your situation, please feel free to contact us, prior to ordering, and for a small charge, we can work with you to adjust the 1515 extrusion lengths, as needed.

If your project requires additional metal parts, we are happy to discuss making a custom part for your needs.  Please feel free to contact us for a quote.

All 713Maker.com products are designed and produced in our home-shop here in the USA